4' Protector XStream Hood Assembly

• Nominal Width: 4'
• Region: U.S. and Canada, International
• Blower Requirements: Remote blower required
• Conformance: ANSI Z9.5, ASHRAE 110, ASTM E84, CAN/CSA      C22.2, NFPA 45, SEFA 1, UL
• Enclosure Height: 59.0"
• Lighting: LED
• Shipping Weight: 440 lbs
• Dimensions: 48.0"w x 37.7"d x 59.0"h
• Electrical: 100-115 volts, 50/60Hz, 10 amps

Features (All Models)

• By-pass airflow design with variable air volume compatibility
• Eco-Foil Air Foil with aerodynamic Clean-Sweep airflow openings
• Cord-Keeper Slots on left and right side of air foil
• Upper Dilution Air Supply
• Glacier white powder-coated steel exterior
• Rear Downflow Dual Baffle System
• Chemical-resistant, fiberglass-reinforced, composite panel liner and  baffles with flame spread index less than 25 per ASTM E84. Baffles are  removable for cleaning
• Opti-Zone Baffle with tapered slots
• Tempered safety glass vertical-rising sash with cable and pulley
• Powder-coated sash handle with aerodynamic Clean-Sweep openings
• 37.5" (95.3 cm) high sightline from the work surface to the header panel
• Removable front and side panels, and front and interior service access panels for access to plumbing and electrical wiring
• Pre-wired LED lighting with vapor-proof design and ADA-compliant light and blower switches. Lighting is rated for 50,000 hours
• Sash stop located at 18" (45.7 cm) sash opening position
• Powder-coated stainless steel, 12.8" (32.5 cm) ID exhaust connection(s).

 Protector Standard Storage Cabinets support Labconco fume hoods and may  be used for storage and venting of small laboratory instruments and mild  acids and other reagents. 

• Durable epoxy-coated steel construction
• Attractive glacier white exterior complements laboratory casework and Labconco fume hoods.
• Manual-closing, non-locking door(s)
• Include four leveling feet and one 8" filler panel to increase cabinet depth from 22" to 30".
• Support loads up to 800 pounds.
• Cabinet Width: 48" (122 cm)
• Door(s): Dual, Manual Close
• Filler Panel Depth: 8.0" (20.3 cm)
• Maximum Base Height: 36.75" (93.3 cm)
• Minimum Base Height: 35.5" (90.2 cm)
• Storage Type: Non-chemical general storage
• Weight: 150.0 lbs
• Dimensions: 48.0" w x 22.0" d

 4' SpillStopper Work Surface, 30.0" deep.

 SpillStopper Work Surfaces are molded from a special formulation of  corrosion-resistant epoxy resins. They are dished and contoured to conform to the interior liner of Protector Laboratory Hoods. The front edge has a large radius to aerodynamically direct airflow into the fume hood. Pre-drilled holes for venting and plumbing passthroughs are provided. Some include 6" x 3" cupsink cutouts. 

• Cupsink cutouts: Left rear cupsink cutout
• Hood, Enclosure or Glove Box Width: 4'
• Weight: 110 lbs
• Dimensions: 48.0"w x 30.0"d x 1.25"h

 Guardian Digital Airflow Monitor senses and alerts the operator to low  airflow conditions. Each monitor includes a face plate with circuit  board, electrical power pack, vinyl tubing, side wall flow tube adapter  and wiring instructions. From the monitor's face plate, the user can  easily select and calibrate a setpoint between 50 and 250 fpm using a  velocity meter. An LCD displays actual face velocity. If the hood's face  velocity falls below the programmable set point, an audible alarm  sounds and the an alarm indicator glows red. The audible alarm can be  muted with one touch. 

Kit includes copper tubing, brass valve and orange knob/connector. Max. flow rate of 23.7 CFM. Max. working pressure of 40 psi.

Kits mount on the right or left side of any Protector Premier, XStream,  XL, XLE or PVC Hood. Each kit includes one remotely-controlled service  fixture with valve and 0.25" diameter tubing, color-coded fixture knob  and color-coded hose connector. Inlet tubing is not included.

 Kit includes one remotely-controlled gooseneck with brass valve and  0.375" diameter copper tubing and green fixture knob. Inlet tubing is  not included. Includes green epoxy-coated brass rigid/swivel gooseneck.  Max. flow rate of 3.5 GPM (13.2 LPM). Max. working pressure of 40 psi.

Gooseneck Fixture Kits mount on the left or right side of any Protector  Premier, XStream, PVC, Stainless Steel, XL or XLE Laboratory Hood with  24" to 30" interior depth.